Segway Ninebot F3/F3 Pro Error Codes and Solutions: Complete Guide

The Segway Ninebot F3/F3 Pro Error codes and solutions guide helps you quickly identify and fix issues on your scooter.

Each error code corresponds to a specific malfunction. Understanding them allows you to react quickly and avoid further damage.

Below is the complete list of error codes, sorted in ascending order, with explanations and solutions.

Error 10 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller communication error.

Solution:
First, check if the rear light works properly when braking. If it doesn’t, replace the taillight or its cable.

Next, remove the handlebar and inspect the connections. Make sure the pins are not bent and cables are properly connected.

If the issue persists, open the deck and unplug components (motor, lights, battery communication cable) to isolate the faulty part.

If the error disappears, the issue comes from one of the disconnected components. If not, replace the dashboard.

Error 11 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller current error.

Solution:
Restart the scooter.
If the issue remains, replace the controller.

Error 13 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller MOS error.

Solution:
Restart the scooter.
If the issue persists, the controller needs to be replaced.

MOS refers to MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor), a component that regulates electrical power inside the controller.

Error 14 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Throttle malfunction.

Solution:
Make sure the throttle returns to its neutral position before powering on.

If it’s stuck, loosen the screw under the throttle with a 3mm hex key, adjust it, and tighten gently.

If the problem continues, replace the throttle.

Error 15 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Left brake error.

Solution:
Check if the brake lever returns properly.

If not, reset its position or replace the left brake lever if necessary.

Error 16 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Right brake error.

Solution:
Same as for the left brake.

Ensure proper lever movement and replace it if needed.

Error 18 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Motor Hall sensor error.

Solution:
Restart the scooter.

If the issue persists, it may be a motor or controller problem. Replacing the hub motor is usually the first step.

Error 19 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Battery voltage error.

Solution:
Restart the scooter.

If the issue remains, the battery may need to be replaced.

Error 24 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller voltage error.

Solution:
Restart the scooter.

If the error persists, replace the controller.

Error 25 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Dashboard communication error.

Solution:
Restart the scooter.

If necessary, replace the dashboard.

Error 26 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: VCU storage error.

Solution:
Restart the scooter.

If the problem persists, replace the dashboard.

Error 30 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Charging temperature too low.

Solution:
Let the scooter sit at room temperature until it rises above 5°C before charging.

If the temperature reading is incorrect, the battery may be faulty.

Error 31 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Program error.

Solution:
Restart the scooter.

If the issue continues, replace the dashboard.

Error 35 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Invalid serial number.

Solution:
Connect the scooter to the Segway app and rewrite the serial number following the instructions.

Make sure the app is up to date.

Error 55 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller overcurrent.

Solution:
Slow down and let the system recover.

If the problem persists, the controller may need to be replaced.

Error 56 – Segway Ninebot F3/F3 Pro Error codes and solutions

Problem: Controller overload.

Solution:
Reduce speed and restart the scooter.

If the issue remains, the controller should be replaced.

Prevent errors with proper maintenance

Most Segway Ninebot F3/F3 Pro Error codes and solutions are linked to wear, electrical issues, or lack of maintenance.

Regularly checking cables, connectors, and key components helps prevent most problems.

Good maintenance means better reliability, improved safety, and smoother rides every day.